Wind Hog W100 1000w (2000w Peak) 12v, 24v Wind Turbine w/Charge Controller

The WindHog 100 series turbine is rated at 80kwh of production a month in a 10mph average wind speed. No wind turbine on the market is built in Alaska for Alaskan Weather.  We receive some of the roughest winds in North America.  It is not uncommon to see over 100mph gusts every winter.  These turbines have a proven track record that can't be beat.  Everything is overbuilt to exceed requirements for extreme conditions. 

This unit is available in 12, 24 systems. Please specify voltage below.

Chassis is made out of 3/16" plate with 3/4" square tubing (very strong) and 1/8" plate for tail.  Up to 2000 Watts in 75mph gusts.  With MPPT Controller. 

Blade start up speed is only 3.8MPH - Power up speed is 7 MPHts, and Stainless hubs NO ONE!
 
2000 Watts plus potential power! -

One Year warranty 

• PMA has no brushes, very dependable!

   

• True PMA we use specially designed n52 Industrial magnets with over 400lbs of pull force far exceeding any competition currently out there.
• Comes with 5 T6 6061 Aluminum beawindhog blades.
• Stainless ball bearing slip ring to keep wires from tangling.
  beawindhog blades are by far the best blades in the business.
• Fits on 1.5" schedule #80 pipe. This utilizes the first industrial 10 hardened Stainless Steel ball bearing mount with locking collar.  This allows the turbine to turn into the wind at only 2mph of wind.  More than 10 percent of power is lossed due to the turbine not turning all the way into the wind.
• 200,000 hours+ of rated bearing life. New bearings cost only $5.00
• Stainless 5 blade hub double thick compared to the competition (1/4" hardened stainless hub)
• All welded chassis with 12" square tail fin
• 3/16" plate chassis extra thick for commercial install
• 1/2" square iron tail stem all welded no bolting for installations of 20 years or more.
• New alternator design with new blades allow for a perfectly silent turbine
• We manufacture the turbine, the wire, and the charge controllers from the ground up so there is nothing but quality in every custom built turbine. 
• Stainless Bolts and locking nuts built to last a lifetime!
• Makes 63" diameter turbine.
• Weighs 50 lbs.
• Commercially wound stators are done by machine and then dipped and baked for over 5 hours with 5 separate layers of lacquer.  No hand wound knock off or junk stators that won't last over a year because the windings fall into the rotor.  These stators are made by a factory specifically for longevity and industrial use.
• Entire unit is primered and then coated 3 layers deep of gold lacquer or other color if you choose.  PMA's are coated in epoxy paint and will look nice for 50 years.
• 1/4" Hardened stainless steel hub is impacted onto the PMA so you never have to worry about it slipping or becoming loose over time
  
• Blades are 28" long with a 10" T1 hardended steel hub.  Fasteners are included.
  
• Permanent Magnet alternator for efficient power.
  
• No electronics in alternator
  
• 3 Phase output allows power to get to controller more efficiently with less expensive wire
  
• Stainless slip ring
  
• 1-15/16" cast iron greaseable bearing for mounting.
  
• All steel no plastic all welded design
  
• Stainless Sealed Alternator Bearings.
  
• Survival 135mph
  
• Breaking system: Electronic
  
• Unit weight is 50lbs
  
• Controller included.